- #How to install spark plug tube seals how to#
- #How to install spark plug tube seals driver#
- #How to install spark plug tube seals manual#
- #How to install spark plug tube seals professional#
Make certain the new plug is set at the correct gap.Basically you are going to do the same steps as "remove" only in reverse.If there is still no spark the problem is most likely a faulty spark plug wire. If it doesn't, try the same test with a new plug. Hit the ignition and see if the plug gives off a good spark. Clean and set the gap of the plug and then connect it to the spark plug wire. If the starter works but the engine won't catch it may be the plug or the spark plug wire.Use the gap gauge to set the gap and then reinstall. If you have pulled it just to clean it you can use WD 40 or fine grade sandpaper to remove carbon buildup. If so you may have a break in the engine seal. Even if you plan to replace the plug with a new one, inspect it and see if it's wet or smells of raw fuel.If the plug is difficult to move, spray a little WD 40 around the base and wait a minute.
#How to install spark plug tube seals driver#
If you don't have the manufacturer's tool use a socket, driver and extension and do the same thing. With the boot off slide the OEM plug puller tool over the plug and turn counterclockwise to unscrew.This may require a bit of effort so look to see where your hand is going to go when the boot snaps free to avoid a scraped knuckle. Grab the spark plug wire boot and pull in the same direction that the plug is pointing.The last thing you need is debris falling into the engine once you have pulled the plug. Spray a little WD 40 around the boot and the surrounding area and then wipe clean.If you are unsure where the spark plug is just follow the spark plug wire (blue or red) to the boot.
#How to install spark plug tube seals manual#
If you don't have the manual check the manufacturer's site online and see if they have one for download. Refer to your OEM manual to determine which piece(s) of plastic you need to remove to gain access to the spark plug.OEM Spark Plug Pulling Tool or a socket, driver and extensions.Screwdriver (to remove exterior panels).
#How to install spark plug tube seals professional#
Our tips are intended to show you that this repair can be done as a DIY project saving you professional labor costs and a more enjoyable ATV experience. When in doubt, follow the OEM instructions. Obviously different brands have different engine mounting configurations meaning the location of the spark plug and how easy it is to access will vary. The steps we provide below are general in nature and are not meant to replace the instructions found in your OEM owner's manual. Check the bolts holding the pipe to the engine to ensure a secure fit. Your exhaust system is another component that is accessible in most models when you have sufficient exterior panels removed to get to the spark plug. A common "won't start" problem is often the result of hard riding loosening the bolts from the battery terminals. Make certain that the bolts on the battery cables are firmly attached to the battery posts. Pulling off parts is the real time consumer for this task.īecause it takes a bit of work to "open up" your ATV it's a good idea to check a couple of items while they are easily accessible. On an ATV you have to remove plastic (exterior panels) to expose the plug and depending on your brand that could be a lot of plastic.
However, unlike a car you can't pull a handle and pop the hood to get to the spark plug. While Your at it:Īctually pulling the plug, inspecting and replacing it only takes 5 to 10 minutes. If these occur it's time to pull the plug and determine if it is the problem or some other component is the cause. This assumes of course that your engine is running normally and you are not experiencing problems like a "rough engine" or an engine that fails to catch while the ignition is turning over. Generally speaking you will want to replace the spark plug(s) after each 100 hours of use.
#How to install spark plug tube seals how to#
How To Inspect, Replace, and Install ATV Spark Plugs When to Replace Your ATV Spark Plug(s)
0 kommentar(er)
